For restaurants, offices, shops and venues with brick and pavers

Commercial brick and paver pressure washing in Austin

Bailey & Bear Cleaning provides commercial brick and paver pressure washing in Austin and about 30 miles around it, cleaning brick walls and walkways, concrete and stone pavers, courtyards and venue patios at restaurants, offices, shops and venues on one written scope. The pressure is set to the joints, and one point of contact runs the job.

Get a brick and paver quote Call 512.689.8346Text us

Walkthrough, then written scope · One point of contact · Commercial properties

Key facts

What does commercial brick and paver pressure washing cover?

It covers the brick and paver surfaces a customer or guest walks past at a business: brick facades and planter walls at the entry, brick walkways from the parking area to the door, concrete and stone pavers in plazas and drop-off lanes, interior courtyards, and the paver patios that restaurants and venues fill with tables. Brick at an entry holds dust, spider webbing, tire spray from the drive aisle and the dark band where hands and bags rub the wall. Paver walkways hold gum, spilled drinks, leaf stain and the green film that grows in shaded joints after a wet spring. A restaurant patio adds grease tracked from the kitchen door and the ring of residue under every table. A venue courtyard adds candle wax, confetti and whatever the last event left between the joints. The walkthrough lists each area by surface, so a brick wall and the pavers at its base are not quoted as one job. Concrete lots, dumpster pads and drive-thru lanes sit with commercial pressure washing across Austin properties, and the page you are on is only about the brick and the pavers.

How is the pressure set differently for brick than for pavers?

Brick is washed for its mortar and pavers are washed for their sand, so neither gets the setting a concrete slab would. On brick, the weak point is the mortar between the units: it is softer than the brick face, and a tight fan held on a joint carves it out and leaves a line that reads as damage from the sidewalk. The crew keeps the pressure low, lets the cleaning solution sit, and rinses from the upper courses of the wall downward so dirty water never runs over a section that is already clean. On pavers, the weak point is the joint sand that locks each unit to its neighbors. Pressure aimed into the joint empties it, and pavers without sand rock underfoot and start to spread. The fan is run across the joints rather than into them, with a surface cleaner on the open runs and a wand only at edges, steps and drains. Every property also gets a small test patch somewhere out of sight before the most visible wall or walkway is washed, which shows what your brick and your pavers come back to rather than what they come back to in general.

Which Austin businesses book brick and paver washing?

Restaurants, office buildings, retail centers and event venues book it most, usually for the surfaces closest to the front door. A restaurant with a paver patio tends to book it on a recurring schedule because grease and spilled drinks build up on the same tables every week; the detail on patio service for restaurants sits on washing paver patios at Austin restaurants. Office buildings book it ahead of a tenant event or a leasing tour, when the brick at the entry and the paver path from the garage are what visitors see first. Event venues book it for courtyards and patios between events, when the reset after one booking has to be finished before the next one walks in. Limestone walls and limestone paving take a different method than brick does; see limestone cleaning for Austin properties. For property managers who want to see what goes into a pressure washing request before calling, there is a pressure washing checklist for Austin properties.

Where do the wash water and the debris go on a brick or paver job?

The plan for both is agreed at the walkthrough, before the quote. Loose debris comes first: leaves, gum wrappers, cigarette butts, broken glass and confetti are swept and bagged dry before any water goes down. We haul off the debris we clear, so nothing is left in the dumpster corral for the property team to find. Wash water from a brick wall or a paver walkway is mostly rinse water, but a restaurant patio near the kitchen door carries grease and food waste, and that water is handled differently near storm inlets. The walkthrough also confirms which spigot the crew can use, whether it holds pressure, and who it is metered to, so water is never something discovered on the night.

When is brick and paver washing scheduled at an open business?

Most brick and paver washing at an open business runs after close, overnight or before doors open, so the walkways are dry and clear when the first customer arrives. A restaurant patio is usually washed after the last service, a retail walkway before the stores open, and an office plaza before staff arrive. Large plazas are split by boundaries the property already has, such as a step, a planter edge or a change in paving pattern, so the work never stops in the middle of a run and leaves a visible line. Venues usually book the wash between events, and the written scope says which areas are done each visit when a courtyard and its patios are spread over two nights. We confirm crew availability before booking each visit. Venue and restaurant managers with brick or paver surfaces can call 512-689-8346 to set up a pressure washing walkthrough.

What should a venue send for a brick and paver quote?

Restaurants, venues and office properties should send the surface type (brick, concrete pavers or stone pavers), the square footage or linear feet, and the date the work has to be finished. Other paved areas: entry walk and plaza sidewalk washing in Austin and dealer lot and fleet yard washing in Austin.

Frequently asked questions

Can a brick wall be pressure washed without washing out the mortar?

Yes, when the pressure stays low and the fan is kept off the joints. Mortar is softer than the brick around it, so the wash leans on dwell time and a rinse, and any joint that is already loose is photographed at the walkthrough before work starts.

Why do pavers lose their joint sand after some washes?

Because a narrow tip pointed into the joints blows the sand out, and pavers without sand start to shift. Our crews run the fan across the joints rather than into them, and joints that are already empty are noted on the written scope.

What is the white haze that shows up on commercial brick after rain?

That is usually efflorescence: salts carried to the face of the brick by moisture. A wash can lift what is on the surface, but the cause is water moving through the wall, so the scope names it as a separate problem instead of treating it as dirt.

Is brick and paver pressure washing in Round Rock or Cedar Park inside your service area?

Yes. Round Rock, Cedar Park, Pflugerville, Bee Cave and Buda are inside our service area of Austin and about 30 miles around it, and a plaza or patio there gets the same walkthrough and written scope.

Interior janitorial and other one-time jobs sit on the full list of commercial cleaning work we take on. When the surfaces are ready to be walked, ask for a written brick and paver washing quote.

Request Cleaning Support

Tell us what needs to be cleaned, reset, turned over, or covered.